# How to fix a muddy mix > A muddy mix is too much in the low mids, roughly 200 to 400 Hz, piling up across parts. Find the part adding the most with the band playing, then cut it there. Page: https://mixchops.com/learn/fix-a-muddy-mix By [Dan Murtagh](https://danmurtagh.com/about) · Updated 3 October 2026 **Short answer:** mud is too much energy in the low mids, roughly 200 to 400 Hz, piling up because almost every instrument has some there. The fix is rarely one big cut on the whole mix. With the band playing, find the one or two parts adding the most, cut them there, and high-pass the parts that don’t need low end. Then check it on more than one system. > **Demo** (plays in the browser on this page): The guitar from a funk mix with a 7 dB bump at 250 Hz, the mud zone. Flip **Clean** and **Muddy** with the band playing, then on its own. Listen to what the bump does to the whole mix, not just the guitar. Both sides play at the same loudness. ## What mud is A muddy mix sounds thick and woolly. Notes blur into each other, words lose their edges, and the mix gets bigger without getting clearer. It builds up in the low mids because almost everything has energy there: guitars, keys, the upper part of the bass, the body of the kick, the chest of a voice, and the reverb on all of them. No one part has to be wrong. It’s the total. ## Find the part 1. **Listen with everything playing.** Ask which part, if it dropped out, would clear the mix up the most. 2. **Mute rather than solo.** Drop one part out at a time and listen to what happens to the rest. Soloed, a part with plenty of low mids can just sound warm and full. It’s in the mix that it clouds things. 3. **Check the usual suspects:** rhythm guitars and keys playing in the same register, pads, the body of the kick, the upper part of the bass, the chest of the vocal, and reverb. ## Cut it there - **Find where that part is thickest.** Sweep a boost through roughly 150 to 500 Hz on it, listen for where the mud jumps out, then turn the boost into a cut of the smallest amount that clears it. - **Use a wider cut than you would for a ring.** Mud is usually broad. A narrow cut is for a single ringing note. - **High-pass the parts that don’t need low end,** and check each one in the mix. Leave the bass and kick their low end: they’re carrying it. - **Cut where it’s piling up, not on every track,** or the mix goes thin. ## Check it - **At the same level.** A cut makes things quieter, and quieter can sound worse even when it’s better. Flip the cut off and on with the levels matched. - **On more than one system.** Headphones and rooms both play tricks in the low end. [Mixing on headphones](https://mixchops.com/learn/mixing-on-headphones) has a check. - **Against a record you like,** at the same loudness, in the same style. ## Questions ### What frequency is mud? Roughly 200 to 400 Hz, the lower part of the low mids. Engineers draw the line in slightly different places, and where a part’s mud sits depends on the instrument, so find it by ear. ### Should I cut 250 Hz on everything? No. Cut the parts that are adding the most, where they’re adding it. Cut the low mids out of everything and the mix loses its body and goes thin. ### Can mastering fix a muddy mix? Only a little. A mastering EQ works on the whole mix, so a cut there turns the low mids down in every part, thinning the parts that weren’t muddy too. Mud is fixed best in the mix, on the parts causing it. ### Is my mix muddy or is it my headphones? It could be either. Headphones and untreated rooms can add or hide low end. Check the mix on a few systems: if it’s muddy on all of them, it’s the mix. ## Find the instrument *that’s muddy.* Fix the Mix plays a full mix as separate instruments, and one of them has a problem: muddy, boomy, boxy, honky, ringy, harsh or brittle. Name it, find the instrument, and cut it there. Soloing costs points, so you learn to find it with the band playing. Solo to Context shows how a move that sounds right on its own can sound different in the track. [Train it in Fix the Mix](https://mixchops.com/eq/fixmix) Then: [Solo to Context](https://mixchops.com/eq/context) · Free, in your browser, no account ## More in Learn - [What is EQ?](https://mixchops.com/learn/what-is-eq): What an equaliser does, heard on a mix - [Parametric EQ](https://mixchops.com/learn/parametric-eq): Frequency, gain and Q - [High-pass and low-pass filters](https://mixchops.com/learn/high-pass-low-pass-filters): Including the high-pass on a vocal - [Shelving EQ](https://mixchops.com/learn/shelving-eq): High shelf, low shelf, and a bell - [Mix problems you can hear](https://mixchops.com/learn/mix-problems): Muddy, boxy, harsh, sibilant, dull - [Mixing on headphones](https://mixchops.com/learn/mixing-on-headphones): What they hide, and how to check - [How to train your ears for EQ](https://mixchops.com/learn/train-your-ears-for-eq): A routine, and the bands people mix up - [Critical listening](https://mixchops.com/learn/critical-listening): What it is, and how to train it - [How to find resonant frequencies](https://mixchops.com/learn/find-resonant-frequencies): Boost, sweep, cut - [Subtractive EQ](https://mixchops.com/learn/subtractive-eq): Cut first, and how to practise it - [All of Learn](https://mixchops.com/learn): Every explainer and guide, and what it trains